World-Designs-Forum  

Go Back   World-Designs-Forum > The Coffee Bar
Register FAQ Members List Calendar Gallery Today's Posts Mark Forums Read

The Coffee Bar Drop in for a chat or say hello if you're a new member!

Reply
 
Thread Tools Display Modes
  #1  
Old 17th January 2024, 12:33 PM
Gosfried Gosfried is offline
Junior Member
 
Join Date: Jan 2024
Location: Oxford
Posts: 2
Default KT88 amp popping

Hi all
From a new member. Morning.
I have a problem that my WD KT88 amp makes a faint random sporadic popping and occasionally scraping noise only on L channel. I have tried replacing and swapping the first valves in the chain but it is still there. Any ideas what I should try next?
Many thanks
Gosfried
Reply With Quote
  #2  
Old 18th January 2024, 08:18 AM
bob orbell bob orbell is offline
Senior Member
 
Join Date: Nov 2009
Location: kettering northants.
Posts: 2,731
Default Re: KT88 amp popping

Hi, and welcome, if you had not metioned the scaping sound, I would have said that the issue was static charge inside the output transformer, but, because of the scraping sound it is more than likely a poor soldered joint, or component beaking down, before we continue, are any of the KT88 valves glowing red, if so do not switch on again, if not you can connect the amp to some speaker and place it on its rear end, remove the base plate and with a PLASTIC proder try gently moving the wires and components on the left chanel and listern, this is called a wiggle test, NOTE, THERE ARE "LETHAL" VOLTAGES IN THE AMP, be caerfull. Bob
Reply With Quote
  #3  
Old 18th January 2024, 11:37 AM
John Caswell John Caswell is offline
Super Moderator
 
Join Date: Dec 2005
Location: Wokingham, Berkshire
Posts: 1,780
Default Re: KT88 amp popping

Sounds (pardon the pun) like a noisy resistor to me. If you are stuck or don't know what you are doing bring it to me I am SE of Reading.

John

Last edited by John Caswell; 18th January 2024 at 11:38 AM. Reason: Adding info
Reply With Quote
  #4  
Old 18th January 2024, 03:09 PM
Gosfried Gosfried is offline
Junior Member
 
Join Date: Jan 2024
Location: Oxford
Posts: 2
Default Re: KT88 amp popping

Dear John and Bob
Thank you for your quick replies. The KT88s are not glowing red, and the amp is performing normally L and R despite the occasional popping noises. I cannot look inside the amp which I built btw 7 years ago, for a few days. But when I can get it on the bench I will definitely try the wiggle test. Do either of you recommend a cold spray test, on the resistors? Also the most stressed resistors in the L input chain are presumably the anode/cathode load resistors on V1 and V2 - would you agree that that would be a good place to start?
Best
Gosfried
Reply With Quote
  #5  
Old 18th January 2024, 03:24 PM
John Caswell John Caswell is offline
Super Moderator
 
Join Date: Dec 2005
Location: Wokingham, Berkshire
Posts: 1,780
Default Re: KT88 amp popping

Hi Gosfried,
Yes go for the wiggle test first, then freezer/hot air gun/hairdryer next. I use all these in tracing something like this.
Start at the first valve then move onto next one. You could also disconnect the feedback R/C, this will of course ramp the gain up but as there is no signal it won't matter too much and can help in localising the fault.

John
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 04:38 PM.


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright World Designs