World-Designs-Forum  

Go Back   World-Designs-Forum > World Designs > Problems
Register FAQ Members List Calendar Gallery Today's Posts Mark Forums Read

Problems For questions and answers re World Designs Projects

Reply
 
Thread Tools Display Modes
  #1  
Old 5th March 2020, 08:39 PM
G Willis G Willis is offline
Member
 
Join Date: Mar 2017
Location: UK
Posts: 43
Unhappy Hum from Pre3 Cathode/Follower and WDKT88

I have upset something moving my equipment. Since the move I have been having a problem with hum from my WD-KT88XL and Pre3 CF. The hum comes and goes.

Powering up today I am hearing a steady hum on both channels which sounds like a combination of G2 and G3 on a piano. G2 is 97Hz so I think given my imperfect pitch this is mains hum.

With my pre-amp powered down a louder, lower 50Hz hum predominates. Switching the pre back on, the 50Hz the hum diminishes and the higher hum is heard again.

The volume or input selector of the pre-amplifier has no effect on the hum.

Unplugging the interconnects causes the hum to almost vanish – there is some transformer noise which is audible over a quiet 50Hz mains hum. I think this is about the same level of quiescent noise produced by the equipment before the move.

Powering down the power amplifier causes the noise to momentarily become louder.

With my DAC plugged directly into the power-amp using the same interconnect cables there is no hum above the normal quiescent level. (It has a built in pre-amplifier)

Any ideas of how to go about looking for this? The obvious culprit is the CF but I cannot see anything wrong with it. I understand that earth loops are caused by two connected devices having different ground potentials but I am not sure how this could arise.
Reply With Quote
  #2  
Old 6th March 2020, 07:58 AM
bob orbell bob orbell is offline
Senior Member
 
Join Date: Nov 2009
Location: kettering northants.
Posts: 2,731
Default Re: Hum from Pre3 Cathode/Follower and WDKT88

It is possible that the umbilical lead is not making a good all round connection, try a wiggle test here. Bob
Reply With Quote
  #3  
Old 6th March 2020, 02:49 PM
Phil Y's Avatar
Phil Y Phil Y is offline
Senior Member
 
Join Date: Jul 2006
Location: Bristol, UK
Posts: 816
Default Re: Hum from Pre3 Cathode/Follower and WDKT88

Hi Graham,

You have moved your gear you say, so are you using different mains sockets to before or perhaps a different extension lead? A poor earth connection is a possible cause, check things over.
Earth loops are in deed caused by earth currents, something as simple as using 2 sockets on opposite sides of the room on your system can cause problems.
Earth loop problems can be infuriating, being methodical is the only way.

Does either the amp or Pre have an earth lift fitted?

Phil.
__________________
Commission for Dark Skies (CfDS)
Reply With Quote
  #4  
Old 6th March 2020, 06:24 PM
G Willis G Willis is offline
Member
 
Join Date: Mar 2017
Location: UK
Posts: 43
Default Re: Hum from Pre3 Cathode/Follower and WDKT88

Thanks both. I tried wiggling the umbilical to no avail. I continuity tested it and it seems good. I also visually inspected the PSU an that seems fine.

I did measure about 0.5v AC difference between the ground on the CF and the ground on the power amplifier. I don't know if that means anything.

I unplugged everything and started turning things on one by one but the problem seems to have gone away, at least temporarily.

Is it a good idea to link the groundings of the power amplifier to the pre-amplifier or will having two earth paths potentially make the situation worst?
Reply With Quote
  #5  
Old 6th March 2020, 07:34 PM
G Willis G Willis is offline
Member
 
Join Date: Mar 2017
Location: UK
Posts: 43
Thumbs up Re: Hum from Pre3 Cathode/Follower and WDKT88

I connected the two amplifiers ground posts together and noise decreased
Reply With Quote
  #6  
Old 11th March 2020, 09:53 PM
G Willis G Willis is offline
Member
 
Join Date: Mar 2017
Location: UK
Posts: 43
Default Re: Hum from Pre3 Cathode/Follower and WDKT88

All red herrings. It turned out to be the bloody kitchen light. I shall have to ban its use. Any recommendations for mains conditioning etc?
Reply With Quote
  #7  
Old 11th March 2020, 11:23 PM
bikerhifinut bikerhifinut is offline
Senior Member
 
Join Date: Jan 2006
Location: Penrith, Cumbria
Posts: 1,128
Default Re: Hum from Pre3 Cathode/Follower and WDKT88

Quote:
Originally Posted by G Willis View Post
All red herrings. It turned out to be the bloody kitchen light. I shall have to ban its use. Any recommendations for mains conditioning etc?
Check the kitchen light and its associated wiring would seem to me to be the first thing if all other possibilities have been eliminated. You may have detected a fault that might be safety related. Or just a duff light fitting. Especially in these days of cheap Chinese LED lighting using borderline rated SMPS.
Switching a light on should not cause any piece of competently designed and constructed audio equipment to show any audible hum. Or for that matter any measurable hum.

A.
Reply With Quote
Reply

Tags
hum, mains, wdkt88xl wdpre3cf


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 10:29 PM.


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright World Designs