World-Designs-Forum  

Go Back   World-Designs-Forum > World Designs > General
Register FAQ Members List Calendar Gallery Today's Posts Mark Forums Read

General For anything else WD or hifi

Reply
 
Thread Tools Display Modes
  #1  
Old 4th December 2021, 05:27 PM
pager8 pager8 is offline
Member
 
Join Date: Mar 2013
Location: Bristol
Posts: 30
Default Suitable Pot

Hi All.
I am looking for a suitable potentiometer to control the brightness of 3mm LEDs assumedly wire wound, 6v-9v input controlling down to 2v-3v. What value would I need to look at?
Thanks in anticipation
Pager8 (Geoff)
Reply With Quote
  #2  
Old 4th December 2021, 07:52 PM
A Stuart A Stuart is offline
Senior Member
 
Join Date: Jan 2006
Location: Selkirk, Scotland
Posts: 403
Default Re: Suitable Pot

I think we need to know more.
Do you know what current they draw, both maximum rated, and at the minimum brightness you will require?
Also their nominal forward voltage drop?
Is this supply 9V ac or dc?
Reply With Quote
  #3  
Old 5th December 2021, 08:56 AM
bob orbell bob orbell is offline
Senior Member
 
Join Date: Nov 2009
Location: kettering northants.
Posts: 2,731
Default Re: Suitable Pot

Geoff, Richard put a chart on here some time ago for the required resistor, or do you want to have the option to adjust the the LED to different levels. Bob
Reply With Quote
  #4  
Old 5th December 2021, 10:07 AM
A Stuart A Stuart is offline
Senior Member
 
Join Date: Jan 2006
Location: Selkirk, Scotland
Posts: 403
Default Re: Suitable Pot

Haven't looked, but can't help thinking a switch and handful of resistors might be less expensive.
Reply With Quote
  #5  
Old 5th December 2021, 10:25 AM
John Caswell John Caswell is offline
Super Moderator
 
Join Date: Dec 2005
Location: Wokingham, Berkshire
Posts: 1,780
Default Re: Suitable Pot

A pot will not adjust the brightness of an LED as it is a diode. It is either on or off. You would need to make some sort of digital control to to switch it on/off in varying mark space ratios, ie as lamp dimmers do.
That said there are quite a few LED types from ultra bright to dim on the market, you have just got to find them!

John
Reply With Quote
  #6  
Old 5th December 2021, 12:27 PM
pager8 pager8 is offline
Member
 
Join Date: Mar 2013
Location: Bristol
Posts: 30
Default Re: Suitable Pot

Thank you all for your replies, What I was looking for is a way of dimming the brightness of a blue LED to match others, I have several in different Amps etc fed from supposedly 6,3 volts and they are at different brightness levels once resistance is determined I would fit appropriate resistor (Or am I misreading the problem)
Regards Pager8 (Geoff)
Reply With Quote
  #7  
Old 5th December 2021, 12:37 PM
A Stuart A Stuart is offline
Senior Member
 
Join Date: Jan 2006
Location: Selkirk, Scotland
Posts: 403
Default Re: Suitable Pot

What am I missing here? Have LEDs changed completely in the last 40 years. Last time I tried playing with what one does, putting 20mA through it was bright, putting (say) 0.25mA through it was dim, no "on-off" behaviour.
Reply With Quote
  #8  
Old 5th December 2021, 03:24 PM
colin.hepburn colin.hepburn is offline
Super Moderator
 
Join Date: Jan 2006
Location: Newtonhill Aberdeenshire
Posts: 2,721
Default Re: Suitable Pot

Hi Geoff/all
Here’s a post and a link Richard posted up for an LED calc that’s simple to use shows you the schematic and the diagram wiring
http://www.world-designs.co.uk/forum...ead.php?t=7948
See link here for the calc here
https://ledcalculator.net/#p=50&v=2&c=4&n=1&o=w
hope that helps
colin
__________________
The Blues man

Turntable Rega 3 custom RB250 with ortofon 2M Blue /other goldring 1042 /WD phono2 /WD CF pre custom converted /WD psu2 /home built JE Labs Single Ended 6SL7/KT66/Speakers Frugal horns Mk1s
Other turntables AR EB101/Thorns TD150mk2/Thorns TD160mk2


If you have trouble reading my posts its because I am a dyslexic member
Reply With Quote
  #9  
Old 5th December 2021, 05:33 PM
John Caswell John Caswell is offline
Super Moderator
 
Join Date: Dec 2005
Location: Wokingham, Berkshire
Posts: 1,780
Default Re: Suitable Pot

Cannot fault what Ali says as I have done the same myself, but I have found that it does depend on the LED, hence my comments.
I can only say try it and see.

John
Reply With Quote
  #10  
Old 6th December 2021, 12:41 PM
Richard Richard is offline
Super Moderator
 
Join Date: Dec 2005
Location: Notts
Posts: 5,357
Default Re: Suitable Pot

<< Thank you all for your replies, What I was looking for is a way of dimming the brightness of a blue LED to match others, I have several in different Amps etc fed from supposedly 6,3 volts and they are at different brightness levels once resistance is determined I would fit appropriate resistor (Or am I misreading the problem)
Regards Pager8 (Geoff) >>


Hi Geoff, the problem may be the supply voltages are different or the leds are different.


You could correct their brightness’ individually by changing the resistor but the visual matching can be a bit hit and miss if the leds are different types, ie, clear or diffused, standard bright, high bright, super bright, ultra bright etc, the naming is various depending on the maker and seller.


I’d buy a set of matching new leds off ebay such as these,


https://www.ebay.co.uk/itm/352163012...EAAOSwhUpcv19e


Then if the supply voltages are all similar 6.3V make all the resistors similar.


The highest dissipation for any of these resistors is 60mW so small 1/8W or 1/4W resistors will be fine.


3mA will give a nice low level indicator; 1K
5mA is brighter perhaps for a brighter room or if it’s not in your direct vision; 620R
10mA very bright; 300R
20mA for laser eye surgery; 150R


I can’t imagine you’ll need the last 2 options


Attached is my 3 box Pre3 set up with blue leds at 3mA, picture and circuit drawing.


If you want to play with the calc put in Supply 6.3V, LED voltage drop 3.3V (for blue leds or other colours as per the ? mark in circle drop-down) and whatever mA up to 20A max for these types, eg,


https://ledcalculator.net/#p=6.3&v=3.3&c=3&n=1&o=w
Attached Images
File Type: jpg blueleds.jpg (28.3 KB, 14 views)
File Type: jpg Pre3led.jpg (58.8 KB, 15 views)
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT +1. The time now is 02:32 AM.


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright World Designs