|
Register | FAQ | Members List | Calendar | Gallery | Today's Posts | Mark Forums Read | Search |
Sources Your DIY source designs (turntables etc.) |
|
Thread Tools | Display Modes |
#1
|
||||
|
||||
Diy Turntable
Hello All
I'm looking at building my own turntable (again) and was after some pointers and tips. am going to use the floppy motor drive idea from - http://www.audioorigami.co.uk/Floppy...pyDIYMotor.htm while looking at a thorens platter on ebay - http://cgi.ebay.co.uk/ws/eBayISAPI.d...MEWA%3AIT&rd=1 thanks Rob |
#2
|
||||
|
||||
Re: Diy Turntable
hi-what are you using to support the platter (main bearing) ?
regards Philip |
#3
|
||||
|
||||
Re: Diy Turntable
Philip
first thoughts are to use a large heavy wooden 'block' which will also have the arm on it. The motor I was going to place in another block. Have seen some nice butchers blocks which may be up to the job,what do you think. Rob |
#4
|
||||
|
||||
Re: Diy Turntable
hi-the thorens platter you refer to only seems to have the bearing spindle.
the platter bearing is a VERY important part and normally is a PRECISION engineered part way beyond diy manufacture. that was what i meant in my last post. regards Philip |
#5
|
||||
|
||||
Re: Diy Turntable
........and I thought belt drives were out of vogue
|
#6
|
||||
|
||||
Re: Diy Turntable
ah - having looked here http://cgi.ebay.co.uk/ws/eBayISAPI.d...MEWA%3AIT&rd=1
I was thinking I could use a valve guide with another ball bearing at the bottom. said who Greg :-) I dont mind if it the fashion or not, its easier to build ;-) Rob |
#7
|
||||
|
||||
Re: Diy Turntable
hi-you will need to engineer for a perfect fit,best not to alter the spindle diameter.bearing surfaces are normally ground to size-not machined.
you could find a valve guide slightly undersize and use an adjustable reamer to open it up ,best of luck. how are you going to mount the valve guide ? i used the platter and bearing from a logic dm101 which i bought cheaply.the bearing bolts to the platter support,in my case a sheet of delrin. regards Philip |
#8
|
||||
|
||||
Re: Diy Turntable
update -
may have access to a thorens platter and bearing! will find out tomorrow. do you have any pictures of your deck? Rob |
#9
|
||||
|
||||
Re: Diy Turntable
hi-not sure how to post pictures.
send me an e-mail or pm with your e-mail address and i'll send you a photo. regards Philip |
#10
|
||||
|
||||
Re: Diy Turntable
I thought that you might like to see the TT I made before I got the Lenco.
http://www.theanalogdept.com/alec_byrom.htm The system has all changed now to an all valve setup and i selling off the Origin Live power supply on ebay but this sounded amazing until i heard the lenco then it was consigned to the loft. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
diy turntable strobe | Rob042 | Sources | 21 | 16th November 2007 06:57 PM |
How about a WD turntable Kit | evozero | Sources | 18 | 22nd August 2006 12:23 AM |
Turntable Signal to Noise Ratio | Primalsea | Sources | 20 | 21st July 2006 08:10 AM |
Luxman turntable | bigbill | General | 1 | 14th May 2006 02:59 PM |
AR EB101 turntable Rebuild | colin.hepburn | Sources | 3 | 10th May 2006 10:11 AM |